PDA

View Full Version : '03 Cobra mods - winter 2007



BADASS03SVT
03-20-07, 04:11 PM
yeap..decided to do it. Funny thing is, we go to "capture" the r134 (or whatever it is) and it was empty!!!! go figure..sprung a leak before it was even turned on. so all the lines, condenser, evap and compressor are gone! Condenser was terrible...had to remove the rad overflow (hence spillage) and loosen the rad to tilt it back and yank up the condenser. cleaned up the left side a little bit but have to move some stuff around and dropped about 30lbs off the nose.

http://img.photobucket.com/albums/v482/BBBjake/IMG_0781.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0780.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0779.jpg

BADASS03SVT
03-20-07, 04:12 PM
http://img.photobucket.com/albums/v482/BBBjake/IMG_0783.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0782.jpg

BADASS03SVT
03-20-07, 04:13 PM
also got the rear end to DMC for Strange 33 spline axles, Strange Pro Diff, Strange 4.11's, 9" ends with big bearings and Ford Explorer brakes. Denis is also going to run axle braces from the tubes to the pumkin.
couple pics of last years carnage
http://img.photobucket.com/albums/v482/BBBjake/IMG_0769.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0771.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0774.jpg

BurnTire
03-20-07, 04:14 PM
So with the missing r134 you had weight reduction you didn't know about. LOL

BADASS03SVT
03-20-07, 04:14 PM
and the very empty undersid eof my car right now
http://img.photobucket.com/albums/v482/BBBjake/IMG_0775.jpg

BurnTire
03-20-07, 04:15 PM
What diff did you have in the car that exploded?

BADASS03SVT
03-20-07, 04:15 PM
So with the missing r134 you had weight reduction you didn't know about. LOL

lol yea i guess so!

BADASS03SVT
03-20-07, 04:16 PM
What diff did you have in the car that exploded?

Eaton..had about 20k miles and probably 200+ passes

BurnTire
03-20-07, 04:17 PM
Eaton..had about 20k miles and probably 200+ passes

I knew it. They always seem to be the ones blowing up.

Jacostang
03-20-07, 05:38 PM
Completed the ac delete in my 89 last fall!!! Love it!!!

BADASS03SVT
03-21-07, 09:54 AM
I knew it. They always seem to be the ones blowing up.

yea..gonna try the Strange unit..didnt want to go to a spool as I drive it too much on the street.

50 BMG
03-21-07, 12:03 PM
In my cobra, I drive with the heater on in the summer out here in Phoenix.

You don't need that AC :biglaugh: , just extra weight anyways...

BurnTire
03-21-07, 12:34 PM
In my cobra, I drive with the heater on in the summer out here in Phoenix.

You don't need that AC :biglaugh: , just extra weight anyways...

50BMG = Crazy:biglaugh:

BADASS03SVT
03-24-07, 04:47 PM
well me and a buddy just tossed the auto up in the car and surprise surprise it will not fit between the long tubes without osme slight modifications. it DEFF wont fit between the cat son the H-pipe so you might see me catless..who knows. anyways, took one of the long tubes out to get the tranny up. going to order a catless H Monday and see what I can do about getting the flamge soff the long tubes.

BADASS03SVT
03-26-07, 12:27 PM
Innovators West SFI Balancer
http://img.photobucket.com/albums/v482/BBBjake/IMG_0777.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0778.jpg
some factory Ford parts needed for the swap
http://img.photobucket.com/albums/v482/BBBjake/IMG_0754.jpg

BADASS03SVT
03-26-07, 12:31 PM
Braided tranny line and connecters
http://img.photobucket.com/albums/v482/BBBjake/IMG_0755.jpg

got around to putting my Trunk mat in. cleans up the trunk area really nice and the carpet matches perfectly!
http://img.photobucket.com/albums/v482/BBBjake/IMG_0784.jpg
and the main part this year...Lentech 4r70w
http://img.photobucket.com/albums/v482/BBBjake/IMG_0790.jpg

AZSonicSnake
03-26-07, 12:58 PM
some purty looking parts right there....i wanna help!

BurnTire
03-26-07, 02:20 PM
What did the balancer cost you?

BADASS03SVT
03-26-07, 02:35 PM
What did the balancer cost you?

brand new they are $575...:jaw-dropping:

I got mine used for much cheaper. It is an EXCELLENT piece though as its made to use the Mecto lower pullies WITHOUT the hub. So all you do is bolt the pulley to it and sell the hub to someone that wants one!

BurnTire
03-26-07, 02:52 PM
Big dollar item. LOL

BADASS03SVT
04-04-07, 06:49 AM
shifter mounting brackets

http://img.photobucket.com/albums/v482/BBBjake/IMG_0807.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0808.jpg
then to put in the shifter and adjust the height...PITA btw...
http://img.photobucket.com/albums/v482/BBBjake/IMG_0809.jpg

BADASS03SVT
04-04-07, 07:00 AM
http://img.photobucket.com/albums/v482/BBBjake/IMG_0812.jpg

and some dynomat to seal up the sides of the shifter and dampen some noise

http://img.photobucket.com/albums/v482/BBBjake/IMG_0815.jpg

Viper_ed
04-04-07, 07:51 AM
also got the rear end to DMC for Strange 33 spline axles, Strange Pro Diff, Strange 4.11's, 9" ends with big bearings and Ford Explorer brakes. Denis is also going to run axle braces from the tubes to the pumkin.

I went with the same brakes when I had the rear for my 88 GT done. Here's a pic of the axel tube supports I had done on mine. There's a member on turbomustangs.com (snoopstang) that sells them for $99 shipped. I know he post on numerous Mustang Boards under the same name if you want to contact him. All of the components are top notch.

BADASS03SVT
04-05-07, 09:02 AM
B&M tranny cooler. Got it mounted behind the bumper cover. hsould be able to get some air form the open ducts next to the fo glights.

http://img.photobucket.com/albums/v482/BBBjake/IMG_0819.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0820.jpg

BADASS03SVT
04-05-07, 09:08 AM
got the PI converter installed. Make sure it is seated! I learned the hard way. No matter how silly the directions sound...use them!

http://img.photobucket.com/albums/v482/BBBjake/IMG_0811.jpg
Tranny in the car and the deep pan installed!!
http://img.photobucket.com/albums/v482/BBBjake/IMG_0821.jpg

BurnTire
04-05-07, 11:35 AM
Looks Good!

Viper_ed
04-05-07, 11:42 AM
That is one SERIOUS ASS LOOKING Tranny Crossmember! :bounce:

BADASS03SVT
04-07-07, 03:37 PM
Shifter, new switch installed and 99% of the wiring done...

http://img.photobucket.com/albums/v482/BBBjake/IMG_0833.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0834.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0835.jpg

BADASS03SVT
04-07-07, 03:41 PM
Cooler fully mounted and braide dlines run

http://img.photobucket.com/albums/v482/BBBjake/IMG_0836.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0845.jpg

BADASS03SVT
04-07-07, 03:47 PM
Spring on my clutch pedal...yes...the clutch pedal is still in. It will be utilized as the Trans brake switch. Th elittle switch under the dash is to kill the power to the pedal in case of accidental touching while on the street

http://img.photobucket.com/albums/v482/BBBjake/IMG_0848.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0846.jpg

BurnTire
04-07-07, 04:28 PM
Looking Good. I like the shifter.

BADASS03SVT
04-07-07, 05:42 PM
Looking Good. I like the shifter.

thanks!

BADASS03SVT
04-26-07, 05:02 PM
got this the other day...nice piece..hopefully I measured right!!

http://img.photobucket.com/albums/v482/BBBjake/IMG_0931.jpg
http://img.photobucket.com/albums/v482/BBBjake/IMG_0932.jpg

nice beefy Mark Williams slip yolk

http://img.photobucket.com/albums/v482/BBBjake/IMG_0933.jpg

BADASS03SVT
04-26-07, 05:05 PM
Ford Racing Explorer brake kit for my 9" ends....thats it for parts!!!! (i hope...) just waiting on my rear end which should be all set in a few days!!

http://img.photobucket.com/albums/v482/BBBjake/IMG_0935.jpg

BurnTire
04-26-07, 07:16 PM
I know a few guys have taken GT Brake Brackets and milled out the center hole to clear the 9" bearings. That way you can keep your cobra calipers and use GT rotors.

BADASS03SVT
04-26-07, 07:25 PM
I know a few guys have taken GT Brake Brackets and milled out the center hole to clear the 9" bearings. That way you can keep your cobra calipers and use GT rotors.

no time to mess around right now...the rear end has been at the shop for 6 weeks for a 1 week job due to some unforseen events. ive missed a few things i have gone to every year already and im pretty pissed...just want the car on the road.

BurnTire
04-26-07, 07:54 PM
no time to mess around right now...the rear end has been at the shop for 6 weeks for a 1 week job due to some unforseen events. ive missed a few things i have gone to every year already and im pretty pissed...just want the car on the road.

I hear you on that. I missed too much with my LVL 5 fiasco.

MinGry03
04-26-07, 09:27 PM
Great job on the conversion....Looks great....:pinkthumb: