PDA

View Full Version : BentTire is again Burntire



BurnTire
02-29-08, 08:38 PM
Well BurnTire is back in action after my multi thousand dollar carnage event

Here is my straightened and braced housing thanks to Darryl Smith Race cars.:twothumbsup:
http://www.highperformancestangs.com/gallery/data/521/P2290044.JPG

http://www.highperformancestangs.com/gallery/data/521/P2290043.JPG

Torque Box Straightening and welding from Devin and Shane at PSR:twothumbsup:

http://www.highperformancestangs.com/gallery/data/521/P2210024.JPG

http://www.highperformancestangs.com/gallery/data/521/P2210023.JPG

PSR welding fireman (Ernie) with water bottle in hand.

http://www.highperformancestangs.com/gallery/data/521/P2210027.JPG

http://www.highperformancestangs.com/gallery/data/521/P2290041.JPG

http://www.highperformancestangs.com/gallery/data/521/P2290040.JPG

I had one of those PSR K-members installed for my quest to go 10.0 @ 135

http://www.highperformancestangs.com/gallery/data/521/P2290038.JPG

http://www.highperformancestangs.com/gallery/data/521/P2290039.JPG

http://www.highperformancestangs.com/gallery/data/521/P2290037.JPG

I still need to have the short subs cut out and replaced by the full length version.

Alignment
Reinstall the Anti roll bar

Little bit of dial in and I should be ready to hit the track again:yes:


Thanks to Devin, Shane, and Dan from PSR for the chassis fix, K-member and gear setup.

Also Daryl Smith for getting the rear end housing fixed.

FalconGTHO
02-29-08, 09:10 PM
Since Im a newb, whats the backstory here?

BurnTire
02-29-08, 09:13 PM
Launch and a bunch of stuff went boom.

Tranny, Axles, Axle Tubes, Gears, Torque Boxes, Upper control arms, etc.

FalconGTHO
02-29-08, 09:16 PM
So everything before was stock? Had you just finished mods or had you raced before? Im surprised you hadnt previously welded the torque boxes and axle tubes.

Venomous Bite
02-29-08, 09:48 PM
Looks like you got the extra light weight K member.

wickedcobra
02-29-08, 09:59 PM
Should I dare say you should be good now :biglaugh:

Looks great, what happened to the red K-member?

BurnTire
02-29-08, 10:11 PM
So everything before was stock? Had you just finished mods or had you raced before? Im surprised you hadnt previously welded the torque boxes and axle tubes.

No everything was the same, the battle boxes were only bolted in.
I also went with a twin disc clutch to allow a little slip on launch.

BurnTire
02-29-08, 10:11 PM
Should I dare say you should be good now :biglaugh:

Looks great, what happened to the red K-member?

Still at the shop.

Indy
02-29-08, 11:34 PM
I'm just glad to see your Cobra back on the road. Now go get that 10.0 slip.:highfive:




BTW - All of us at PSR were happy to help ya out.:yes:

AZSonicSnake
03-01-08, 12:41 PM
do i see a psr kmember?!?! i knew jeff would see the light.....woot...

autoxstang
03-01-08, 02:49 PM
Great to see you getting the car back together Jeff. I just hope I can still keep up with you. :tearsofjoy:

The Nunn's
03-01-08, 04:47 PM
Thanks to Devin, Shane, and Dan from PSR for the chassis fix, K-member and gear setup.

Also Daryl Smith for getting the rear end housing fixed.

ya you're welcome too bent-tire, maybe i should have let some of those pretty little sparks on to those nice seats you got...lol:veryhappy:

4Jenna
03-01-08, 05:21 PM
Wow, looks sick Jeff!! That bracing is some good stuff!!!!!

PSR did a kick-butt job on the welding/K-member!!!!!

BurnTire
03-02-08, 01:14 AM
Looks like you got the extra light weight K member. Yes it has clear coat only. No paint like your heavy one:laughing:

BurnTire
03-02-08, 01:16 AM
ya you're welcome too bent-tire, maybe i should have let some of those pretty little sparks on to those nice seats you got...lol:veryhappy: And you too Ernie:Bucktooth:

BurnTire
03-02-08, 01:18 AM
do i see a psr kmember?!?! i knew jeff would see the light.....woot...

Yes it was a Green light. Less Green for me.

93mustank
03-02-08, 11:01 AM
So your coming to club day now?

Venomous Bite
03-02-08, 02:10 PM
Yes it has clear coat only. No paint like your heavy one:laughing:
I believe mine is powder coated, so yeah what up now?:woot1:

sesso
03-03-08, 12:33 AM
Looks good man. I like the welding job also.

Jacostang
03-03-08, 08:45 AM
Yeah!!! Finally I better see that at the show too!!

I talked to Dan briefly the other night about a Dyno-Day at PSR with CMC and Wild West... Test Session???

BurnTire
03-03-08, 10:54 AM
Yeah!!! Finally I better see that at the show too!!

I talked to Dan briefly the other night about a Dyno-Day at PSR with CMC and Wild West... Test Session???

Sounds like a good event to do prior to it getting too hot outside.

ASUSMC
03-03-08, 10:58 AM
Sounds like a good event to do prior to it getting too hot outside.

I agree. Maybe my vehicle will make it off the dyno before blowing up.

BurnTire
03-03-08, 11:03 AM
I agree. Maybe my vehicle will make it off the dyno before blowing up.

LOL.

I have a nice set of used subs that are going to be getting replaced with full lengths. Do you need a set?

ASUSMC
03-03-08, 12:22 PM
No I need a Lightning motor.... Got one?

Dan
03-03-08, 12:28 PM
I believe mine is powder coated, so yeah what up now?:woot1:


yes shaggy yours is semi gloss and jeffs is clear

El Jefe
03-03-08, 02:57 PM
Nice bling bling!!

WildBill
03-03-08, 09:41 PM
ya you're welcome too bent-tire, maybe i should have let some of those pretty little sparks on to those nice seats you got...lol:veryhappy:

Yeah.........He forgot who took his BENT REAR to Daryl Smith too.:hi:

BurnTire
03-03-08, 11:03 PM
Yeah.........He forgot who took his BENT REAR to Daryl Smith too.:hi:

Thanks to Wild Bill and Bad Shot in the office!

Blownsvt
03-05-08, 06:08 PM
are you on an 8.8? i persnally went with a ford 9" and had everything welded up the other day. i am sure that sucked having to rip it out and re do it.. I am tyring to make everything as solid as possible right from the get go.

BurnTire
03-05-08, 07:53 PM
are you on an 8.8? i persnally went with a ford 9" and had everything welded up the other day. i am sure that sucked having to rip it out and re do it.. I am tyring to make everything as solid as possible right from the get go.

Yes I have an 8.8 that is now more expensive than a good 9" setup.

Blownsvt
03-06-08, 08:39 AM
Yes I have an 8.8 that is now more expensive than a good 9" setup.


that not a good thing, i would have just done the 9" is it going to hold up this time?

BurnTire
03-06-08, 09:00 AM
that not a good thing, i would have just done the 9" is it going to hold up this time?

Yes it will hold now with the bracing.

SONIC03SNAKE
03-10-08, 12:00 PM
Looks like some nice quality work there Jeffrey, now all you need is a driver.:Bucktooth: Its cold here, send me a plane ticket and ill come out.:boxing:

WildBill
03-10-08, 12:07 PM
Looks like some nice quality work there Jeffrey, now all you need is a driver.:Bucktooth: Its cold here, send me a plane ticket and ill come out.:boxing:
Yeah..........ol' Jeffy didn't wanna pay for that "driver mod"!:laughing::laughing:

BurnTire
03-10-08, 12:16 PM
Looks like some nice quality work there Jeffrey, now all you need is a driver.:Bucktooth: Its cold here, send me a plane ticket and ill come out.:boxing:
LOL. Can you handle all that power?

WildBill
03-10-08, 12:32 PM
Jeffy should be the best driver ever with all the days off he has!!:laughing::laughing::yes::yes:

BurnTire
03-10-08, 12:35 PM
Jeffy should be the best driver ever with all the days off he has!!:laughing::laughing::yes::yes:

It takes some serious skill to let out the clutch and break everything behind it:biglaugh:

WildBill
03-10-08, 07:56 PM
It takes some serious skill to let out the clutch and break everything behind it:biglaugh:

:laughing::laughing::laughing::laughing::yes:

SONIC03SNAKE
03-10-08, 10:19 PM
LOL. Can you handle all that power?
Who needs power to go fast?:sticktonge: You better hurry up or the wife is going to catch up.:wave:

BurnTire
03-10-08, 10:20 PM
What is that twin screw thing in your house?
I thought you only made love to the Eatons!

SONIC03SNAKE
03-10-08, 10:22 PM
What is that twin screw thing in your house?
I thought you only made love to the Eatons!
Wifes car = Heavy vert= need big power

BADASS03SVT
04-05-08, 12:25 PM
will have to look at your other post...breaking stuff is always fun!! good upgrades!!! that tubing is huge!!! here is mine along with the new ARB installed...its a jungle gym under there!!!


http://img.photobucket.com/albums/v482/BBBjake/IMG_2026.jpg

http://img.photobucket.com/albums/v482/BBBjake/IMG_2359.jpg

BurnTire
04-06-08, 02:01 AM
Looks good. I see you have a little exhaust rubbing. LOL
I had mine designed to miss the pipes.

BADASS03SVT
04-06-08, 05:08 AM
Looks good. I see you have a little exhaust rubbing. LOL
I had mine designed to miss the pipes.

yea..its actually this slp exhaust..its made weird. the arb is supposed to clear up to 3" catbacks and it didnt clear the slp 2.5" at first. the maker was like thats a first. i got it to work though

4Jenna
04-06-08, 12:41 PM
That Kevins ARB?

BADASS03SVT
04-07-08, 05:25 AM
That Kevins ARB?

yeap!

Akuma
04-14-08, 12:49 PM
Wow Jeff, must have been one hell of a launch!

BurnTire
04-14-08, 01:23 PM
Wow Jeff, must have been one hell of a launch!

I thought the rear end left the car.

Venomous Bite
04-14-08, 01:56 PM
Wow a post by Kyle and James in the same month! All we need now is Brian to post and I think the earth would stop spining.

Akuma
04-14-08, 05:09 PM
Wow a post by Kyle and James in the same month! All we need now is Brian to post and I think the earth would stop spining.


Naw, now if Biran and I showed up at pavilions then the world might stop spinning.