PDA

View Full Version : Peugeot 605 16v Turbo



tabakoff
04-20-07, 01:28 AM

BurnTire
04-20-07, 01:37 AM
Sounds like a good project you have going there.

Should be a nice street machine.

Post up some pictures so everyone knows what a Peugeot looks like.

Any mustangs in Bulgaria?

Jeff

tabakoff
04-20-07, 03:02 AM
... :-( Very rarely … These cars cost too much, we cannot afford it in Bulgaria.

However, this is my favorite brand. I saw last Shelby GT500 on pictures …. I had no words, my heart stopped for a couple of seconds.

Even there are no many Mustangs in Bulgaria, it is a prestige, a matter of honor to owe and to drive such a car … no, no …. It is not a car – it is gorgeous and magnificent car.

As regards to my car and my project - here you are some pictures.

This is the car. Peugeot 605, model 1994. An old one, but it worth the money.

http://misho.avproxy.net/Peugeot_605_1_WEB.jpg

This is the turbocharger, compared to an audio CD

http://misho.avproxy.net/GT2860RS_compared_to_a_CD_1_WEB.jpg http://misho.avproxy.net/GT2860RS_compared_to_a_CD_2_WEB.jpg

This is the engine compartment ... tooooooo many tubes and hoses that will be optimized as much as possible:

http://misho.avproxy.net/Engine_Compressor_Pipes_WEB.jpg http://misho.avproxy.net/Engine_View_2_WEB.jpg


I replaced the rear shock absorbers with the only kit available for my car - KONI Special Red Adjustable:

http://misho.avproxy.net/605_KONI_Rear_Adjusting_Ball_WEB.jpg http://misho.avproxy.net/605_KONI_Rear_in_the_box_WEB.jpg http://misho.avproxy.net/605_KONI_Rear_Without_the_Housing_WEB.jpg


I wanted to order this exhaust manifold, but later on I decided to make it 4-2-1 instead of 4-1, because it will improve the performance of my engine:

http://misho.avproxy.net/605_16v_Turbo_XU10J4R_11.jpg http://misho.avproxy.net/605_16v_Turbo_XU10J4R_21.jpg http://misho.avproxy.net/605_16v_Turbo_XU10J4R_31.jpg


This the Aeromotive Fuel Pressure Regulator:

http://misho.avproxy.net/Aeromotive_Fuel_Pressure_Regulator_Front_View_WEB. jpg http://misho.avproxy.net/Aeromotive_Fuel_Pressure_Regulator_Rear_View_WEB.j pg


This is the HKS SSQV Blow-off valve:

http://misho.avproxy.net/HKS_SSQV_Accessories_WEB.jpg http://misho.avproxy.net/HKS_SSQV_Flange_Bottom_View_WEB.jpg http://misho.avproxy.net/HKS_SSQV_Front_View_WEB.JPG http://misho.avproxy.net/HKS_SSQV_Side_View_WEB.jpg http://misho.avproxy.net/HKS_SSQV_Side-Rear_View_WEB.jpg http://misho.avproxy.net/HKS_SSQV_Top-Front_View_WEB.jpg

tabakoff
04-20-07, 03:04 AM
These are the Brembo 4-piston calipers:

http://misho.avproxy.net/Brembo_Alfa_166_Top_View_WEB.jpg http://misho.avproxy.net/Brembo_Alfa_166_Outer_View_WEB.jpg http://misho.avproxy.net/Brembo_Alfa_166_Both_Calipers_WEB.jpg http://misho.avproxy.net/Brembo_Alfa_166_Inner_View_WEB.jpg http://misho.avproxy.net/Brembo_Alfa_166_Logo_WEB.jpg http://misho.avproxy.net/Brembo_Alfa_166_Brake_Pads_WEB.jpg


This is the haltech E8 ECU ... the TPS and Trim module are on the way to Bulgaria along with the JE Pistons and Pauter rods:

http://misho.avproxy.net/Haltech_E8_ECU_WEB.jpg


This is the Innovate LC-1 Wideband Controller mad for Haltech - Australia:

http://misho.avproxy.net/Haltech_Innovate_Wideband_Controller_with_Gauge_WE B.jpg


Here are the Haltech Ignition Coils with built-in commutator:

http://misho.avproxy.net/Haltech_Coils_with_Built-in_Ignitors_WEB.jpg


And finally the VECCO's components ... I expected more from Treadstone intercooler core ... :icon_sad: :sad2::

http://misho.avproxy.net/Intercooler_Bar_n_Plate_Core_18.5x6x3_Vertical_Flo w_w_Tanks_WEB.jpg http://misho.avproxy.net/Intercooler_Core_Close_View_Could_be_Better_WEB.jp g http://misho.avproxy.net/Intercooler_Deformed_Core_WEB.jpg http://misho.avproxy.net/Intercooler_Pipes_n_Silicone_Hoses_1_WEB.jpg http://misho.avproxy.net/Intercooler_Pipes_n_Silicone_Hoses_2_WEB.jpg http://misho.avproxy.net/Intercooler_Treadstone_WEB.jpg

However, people say that even Treadstone's core does not look very nice, it is quite effective ... will see.

BurnTire
04-20-07, 03:57 PM
Mike you have a good looking project in the works there.

Is there a drag strip in Bulgaria or any place to race?

BurnTire
04-20-07, 03:58 PM
Hey HPS members say hello to Mike from Bulgaria.

Our First international member.

:welcome4:

silver03cobra
04-20-07, 05:28 PM
Hello!
Mike nice ride..... looks like you got your work cut out for you.. what kind of power are you looking to get ???
so what other cars do you and your friends play with?

tabakoff
04-21-07, 08:27 AM
Mike you have a good looking project in the works there.

Is there a drag strip in Bulgaria or any place to race?

Yes, we opened the 2007 season last weekend. Tomorrow there will be the first official drag race in Sofia, Bulgaria.

Bulgaria is a small country and there are not too many enthusiasts that are able to start a drag project.

However there are two powerful cars in Bulgaria. The first one is Ford Sierra with modified engine that shows 10.4 sec @ 1/4 mile. The other one is Nissan Skyline with 10.1 sec @ 1/4 mile.

Building more powerful car costs too much. Drags are not very popular yet in Bulgaria, that's why there is only one drag strip in Sofia where I am going to be tomorrow.

There are two race tracks in Bulgaria - one @ Plovdiv and one @ Sofia.

tabakoff
04-21-07, 08:36 AM
Hello!
Mike nice ride..... looks like you got your work cut out for you.. what kind of power are you looking to get ???
so what other cars do you and your friends play with?
My target is 300 - 320 HP @ crank, I believe about 280 BHP. I need for everyday driving in the city and on the highway.

When I finish this project I will open another one for drag. I have one engine "Chochone" - v8, 5.000 l from Mercedes SL 500E. I believe it will kick 1000 HP @ crank at about 25 psi boost. Now I am looking for the proper cassis. But this project will start maybe late autumn.

BurnTire
04-21-07, 10:00 AM
Yes, we opened the 2007 season last weekend. Tomorrow there will be the first official drag race in Sofia, Bulgaria.

Bulgaria is a small country and there are not too many enthusiasts that are able to start a drag project.

However there are two powerful cars in Bulgaria. The first one is Ford Sierra with modified engine that shows 10.4 sec @ 1/4 mile. The other one is Nissan Skyline with 10.1 sec @ 1/4 mile.

Building more powerful car costs too much. Drags are not very popular yet in Bulgaria, that's why there is only one drag strip in Sofia where I am going to be tomorrow.

There are two race tracks in Bulgaria - one @ Plovdiv and one @ Sofia.

The Fast Ford Sierra.
http://memimage.cardomain.net/member_images/10/web/670000-670999/670665_1_full.jpg


Nissan Skyline
http://www.rsportscars.com/foto/09/skyline.jpg

Get some pictures if you can at the drag strip. I would like to see what everyone is racing.

silver03cobra
04-22-07, 01:42 PM
we just got done building a RB25DT (skyline engine) made 539hp @20 psi. Its in a 240sx. ran 13.99@139.04 (needs good tires). How was the drag strip? We whent last night.... Jeff (burntire) went 10.90@127.??mph and there was a 4 door dodge diesel that went 12.82@109.??mph. A Honda civic hatchback with a big turbo went 10.99@12?.??mph

AZSonicSnake
04-22-07, 02:41 PM
wow, very cool stuff. look forward to seein some pics from the drag strip! looks like some fun. keep us updated on your project!!!

btw- welcome aboard!

Indy
04-22-07, 04:44 PM
WELCOME!



Looks like you have a very well planned project going, good luck with it. You should have a pretty nice street sleeper on your hands when its finished.

tabakoff
04-24-07, 06:29 AM
Hi again,

Here are some pics from the drag strip last Sunday. There are some gorgeous cars, I hope you will like them.

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=344

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=345&stc=1&d=1177417560

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=346&stc=1&d=1177417560

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=347&stc=1&d=1177417560

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=354&stc=1&d=1177418596

tabakoff
04-24-07, 06:36 AM
And some more ....

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=349&stc=1&d=1177417967

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=350&stc=1&d=1177417967

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=351&stc=1&d=1177417967

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=352&stc=1&d=1177417967

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=353&stc=1&d=1177417967

tabakoff
04-24-07, 07:38 AM
Now some more simple cars, but with high potential.

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=355&stc=1&d=1177421873

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=356&stc=1&d=1177421873

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=357&stc=1&d=1177421873

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=358&stc=1&d=1177421873

http://www.highperformancestangs.com/forums/attachment.php?attachmentid=359&stc=1&d=1177421873

tabakoff
04-24-07, 07:47 AM
Some Mitsubishi cars
360

361

362


A Seat Ibiza

363

... and one representative from the former East Germany - Trabant. :biglaugh:

364

tabakoff
04-24-07, 07:51 AM
Finally some pictures of an Opel Corsa

BurnTire
04-24-07, 10:48 AM
Those are some great photos. It looks like you have a bunch of people show up for the event. Who had the fastest car?

ASUSMC
04-24-07, 11:27 AM
That is definetely some cool stuff out there. Saw a few cars I recognized and some I didn't.

silver03cobra
04-24-07, 11:35 AM
Those are some great photos. It looks like you have a bunch of people show up for the event. Who had the fastest car?

That gray R34 Skyline....... :pepper:

tabakoff
04-24-07, 01:32 PM
The Skyline GTR showed 10.379 s. He had some launch problems and was a bit slow at first gear, but on higher gears it had amazing performance!!! It passes like F16 at low altitude!!!!

BurnTire
04-24-07, 02:09 PM
The Skyline GTR showed 10.379 s. He had some launch problems and was a bit slow at first gear, but on higher gears it had amazing performance!!! It passes like F16 at low altitude!!!!

Was that race held at an airport?

RockysMom
04-24-07, 07:27 PM
I call them wanna be cars hehehe. What the heck are they anyway??? Are they just baby mustangs waiting to grow? :laughing1: :laughing1: :laughing1:

BurnTire
04-25-07, 12:48 AM
Mike here is a link to a few videos of my runs from Saturday.
http://www.highperformancestangs.com/forums/showthread.php?t=2840

tabakoff
04-25-07, 01:25 AM
Was that race held at an airport?
Yes, that was an airport long time ago, now we use it for drag strip. Soon there will be stands and reinforced concrete safety barriers.


I call them wanna be cars hehehe. What the heck are they anyway??? Are they just baby mustangs waiting to grow? :laughing1: :laughing1: :laughing1:
They are far far away even from baby Mustangs ... :biglaugh: :laughing1:

The small one with "KUPOB" written on the right door is Fiat 126P. This is a very old Fiat, but produced in Poland. The stock engine is 600 cc, 2 cylinder and about 25 HP. Now the engine is 4 cylinder and hits 12.561 s @ 1/4 mile.

The white one with registration plate TX 8333 AX is an old russian Lada Zhiguli. No one knows what is behind the bonnet, but its time is 12.832 s.

Mitsubishi Eclipse - 11.292

Red Mitsubishi EVO - 11.281

Black Mitsubishi EVO - 13.400

Seat Ibiza - 13.710

Bellow the Seat picture you see the ligh blue .... TRABANT, from the former East Germany. The stock engine was 2-stroke 2 cylinder, the new one is 4 cylinder 1600cc, but it still shows above 14 seconds.

The violet Opel Corsa is with 2000cc 16 valve engine, mounted in the boot of the car. Its time is 13.419s.

.................................................. .........................

As I told you people in Bulgaria cannot afford to pay too much money for expensive cars and for performance tuning. But we are eager to do something with our hands, so these results are very good.

Even slowly, but we are growing up and I hope soon we will have some great cars for drag.

BurnTire
04-25-07, 01:36 AM
Those are some impressive times.

How does the track time the races.

Do you have timing like we do here that measures

60 ft
330 ft
660 ft
1000 ft
1320 ft

tabakoff
04-25-07, 03:27 AM
With the existing equipment can be measures only time @ 60 ft and 1320 ft and the terminal velocity.

The new equipment had arrived from the USA.

http://www.tuning.bg/forum/files/04042007096_159.jpg http://www.tuning.bg/forum/files/04042007097_181.jpg

It is wireless and can measure the speed trap at 60 ft and at 1320 ft, as well as reaction time.

BurnTire
04-25-07, 10:39 AM
Do they spray the track with VHT (glue) to make it sticky?

tabakoff
04-25-07, 01:03 PM
No, the organizer do not spray the track with any glue. I am new on drag strips and have never heared about that.

All these timings are without a glue.... I have to propose them to do that, thank you for the idea.

tabakoff
04-25-07, 01:08 PM
Mike here is a link to a few videos of my runs from Saturday.
http://www.highperformancestangs.com/forums/showthread.php?t=2840
Nice runs and very good reaction! Cool!

BurnTire
04-25-07, 01:37 PM
No, the organizer do not spray the track with any glue. I am new on drag strips and have never heared about that.

All these timings are without a glue.... I have to propose them to do that, thank you for the idea.

This is what they use on the tracks

http://www.caswellplating.com/vht/vht_quality.htm


http://www.caswellplating.com/vht/images/trackbitedrum.jpg

VHT TRACKBITE SP-162 is an exclusive consumer formulation designed to offer controlled traction for competition drag racing. VHT TrackBite is a liquid track treatment, which improves traction by means of adhesion and does not soften tires nor the track surface as other imitation products may. SP-162 is packaged in a one gallon bottle.
VHT TrackBite SP-163, Drag Strip Formula, 55
Gallon Drum is a high solids, quick setting liquid
track treatment designed specifically for drag
track racing competition.
This exclusive formulation is designed to offer controlled traction, quicker times and create more exciting racing.
VHT TRACKBITE CONCENTRATE, SP-165 has been engineered for paved oval tracks. Also packaged in 54 gallon drums, this formula is designed to withstand the rigors of extreme cornering loads, while enhancing side bite. Very durable, will not harm track surface or tires as other imitation products may, and will wthstand extreme exposure to the sun's heat. VHT TrackBite Concentrate, SP-165 is also an excellent sealer on freshly ground and/or resurfaced tracks. Used at leading USAC and NASCAR sanctioned paved ovals.
VHT TrackBite has been used by every major drag strip and drag racing sanctioning body since 1972.

BurnTire
04-27-07, 02:26 AM
Any of these Opel GT's around?
I have seen these in the USA from time to time

http://www.opel6070club.com/oulu03/gt70_ulko2.jpg

Opel Funny Car.
I but this runs good.
http://www.nofearmotorsports.com/images/ACFF6A.JPG

BurnTire
04-28-07, 11:10 PM
Well they don't discriminate. The screw people domestically and foreign alike.

BurnTire
05-10-07, 01:39 AM
Mike how is the project coming?

tabakoff
05-11-07, 05:26 AM
:icon_sad: :sad-smiley-047: :hissyfit: Problems and misunderstandings ....

Pauter made the rods for 0.787" pins instead of 0.886". They confessed their fault so I sent them back to Brian Pauter.

JE Pistons made the pistons for 3.386" bore instead of 3.406" ....

I am pretty unlucky guy, this project goes very slow. Without proper pistons and rods I cannot initiate anything. I need them installed inside the engine, then have to assemble the engine and mount it together with the gear box inside the engine department in order to build brand new 4-2-1 exhaust manifold.

I have nothing to do but to wait for the remastered parts .... unfortunately.

BurnTire
05-11-07, 11:22 AM
:icon_sad: :sad-smiley-047: :hissyfit: Problems and misunderstandings ....

Pauter made the rods for 0.787" pins instead of 0.886". They confessed their fault so I sent them back to Brian Pauter.

JE Pistons made the pistons for 3.386" bore instead of 3.406" ....

I am pretty unlucky guy, this project goes very slow. Without proper pistons and rods I cannot initiate anything. I need them installed inside the engine, then have to assemble the engine and mount it together with the gear box inside the engine department in order to build brand new 4-2-1 exhaust manifold.

I have nothing to do but to wait for the remastered parts .... unfortunately.

That stinks.
I know all about getting incorrectly machined parts all too well.

silver03cobra
05-11-07, 09:16 PM
That stinks.
I know all about getting incorrectly machined parts all too well.

HA HA HA thats Jeff's LIFE!!!!!! ha ha ha:rollingfloorrlol:

tabakoff
05-28-07, 04:05 AM
I got my pistons and rods finally!!!! I hope now they are OK.

Here are the pistons:

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_Box_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_1_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_2_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_11_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_12_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_15_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_3_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_4_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_5_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_7_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_8_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_6_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_9_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_13_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_14_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_JE_Pistons_10_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_Total_Seal_Rings_WEB.JPG

tabakoff
05-28-07, 04:07 AM
Here are the rods ...

http://misho.avproxy.net/Top_End_Performance_II_Pauter_Box_5_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_Pauter_Rods_2_WEB.JPG

http://misho.avproxy.net/Top_End_Performance_II_Pauter_Rods_Front_Viewl_WEB .JPG

http://misho.avproxy.net/Top_End_Performance_II_Pauter_Rods_Side_View_WEB.J PG

http://misho.avproxy.net/Top_End_Performance_II_Pauter_Rods_Small_End_WEB.J PG

http://misho.avproxy.net/Top_End_Performance_II_Pauter_Rods_Big_End_1_WEB.J PG

http://misho.avproxy.net/Top_End_Performance_II_Pauter_Rods_Big_End_2_WEB.J PG

http://misho.avproxy.net/Top_End_Performance_II_Pauter_Rods_Big_End_3_WEB.J PG

BurnTire
05-28-07, 10:54 AM
Looks like it is work time for you now Mike.

silver03cobra
05-28-07, 01:18 PM
we used pauter on are RB25DET and VG30DETT that we just got done building both make 530+hp..... great rods... call and ask about the finished size of the big end for oil clear.... i know we had to hone alittle....

tabakoff
05-29-07, 12:42 AM
10x for the advice, I will check that.

5.0Stanger
06-26-07, 08:32 PM
So, how's the engine assembly coming?

The pictures of the pistons and rods showed tons of promise.

Good luck! :pinkthumb:

silver03cobra
06-26-07, 08:49 PM
10x for the advice, I will check that.


what did you find out with the rods???

tabakoff
06-27-07, 03:49 AM
what did you find out with the rods???Big ends were OK and there were no need to hone it at all, most probably they have paid attention to this matter.

Now I have my project in progress.


http://misho.avproxy.net/XU10J4TE_MJT_After_Grinding_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_Being_washed_WEB.JPG
http://misho.avproxy.net/XU10J4TE_MJT_Before_Drying_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_On_Engine_Stand_1_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_On_Engine_Stand_2_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_Honed_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_Fitting_Piston_Oilers_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_Piston_Oilers_WEB.JPG
http://misho.avproxy.net/XU10J4TE_MJT_Crank_Dried_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_How_We_Do_Look_at_9mp_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_Still_Being_Keen_on_Our_work_at_9pm_W EB.JPG http://misho.avproxy.net/XU10J4TE_MJT_Crank_Mounted_and_Rotating_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_Full_Set_of_Rods_and_Pistons_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_Full_Set_of_Rods_and_Pistons_HPS_WEB. JPG http://misho.avproxy.net/XU10J4TE_MJT_HPS_Fantasy_Guy_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_Three_Pistons_Mounted_Inside_1_WEB.JP G http://misho.avproxy.net/XU10J4TE_MJT_Three_Pistons_Mounted_Inside_2_WEB.JP G http://misho.avproxy.net/XU10J4TE_MJT_All_Pistons_Inside_WEB.JPG http://misho.avproxy.net/XU10J4TE_MJT_Packed_for_the_Next_Day_WEB.JPG

BurnTire
06-27-07, 01:56 PM
Looks like you are getting things ready to go.
When is the motor going back in the car?

silver03cobra
06-27-07, 03:14 PM
looks good ! the motor reminds me of a nissan...

5.0Stanger
06-27-07, 10:47 PM
Looking good!

Doesn't he look proud to have gotten somewhere on his project? I hate it when suppliers cause a snag.

Keep up the good work, tabakoff!:pinkthumb:

tabakoff
06-28-07, 12:01 PM
Thank you guys.

The motor is going back under the bonnet this Saturday. Then a brand new 4-2-1 exhaust manifold will be produced on our own. This type of manifold will optimize the mid range revs, all the more that max revs will be up to 7000 rpm. It must be done around July 10. I believe the engine will ignite at the end of July ... I hope so.

Greetings to all of you.

5.0Stanger
06-28-07, 08:16 PM
I have a friend, out here, that has that same type of header/manifold on almost everything he owns. He claims it has the same proven benefits that you speak of, tabakoff. I believe that will help your 4-cyl engine in the midrange, as well.

Good luck with the fab-up of that manifold.

tabakoff
06-29-07, 12:26 PM
As I have read, 4-2-1 is prefferable for engines @ less than 8000 rpm . They have much broader power band. When it comes to top power, 4-1 would be best.

BurnTire
07-26-07, 01:09 AM
Got that motor in yet Mike?

tabakoff
07-26-07, 01:42 AM
Not yet. My wife's father got insultus ... apoplexy, I am not sure for this medical term in English. So I had to stop the project for a while.

The exhaust manifold has just been done. I will post pics in a couple of days. There were no space to fit 4-2-1 header behind the engine so I had nothing but to acquiesce with 4-1 design. In any case it will be much better than a log-type.

I took down the engine again for the final assembling yesterday. When it will be fully assembled, I will put it back in the engine compartment and install the new intercooler, 2.5" turbo pipes, cold air tubes, 2.5" Blow-off alu flange, HKS SSQV Blow-off and 2.5" single throttle flap. A new hand made separate downpipe will be fabricated - one tube for the main flow out of the turbine, and smaller one for the gas through the wastegate. I will join the tubes just before the cat.

Next step will be the fuel delivery system. Finaly the ECU will be installed.

I ahve no idea when the project will be finished, but I have tones of patience. :twothumbsup:

Have a good time. When I have news I will post info.

Greetings to all of you.

Mike

BurnTire
07-26-07, 01:56 AM
Not yet. My wife's father got insultus ... apoplexy, I am not sure for this medical term in English. So I had to stop the project for a while.

The exhaust manifold has just been done. I will post pics in a couple of days. There were no space to fit 4-2-1 header behind the engine so I had nothing but to acquiesce with 4-1 design. In any case it will be much better than a log-type.

I took down the engine again for the final assembling yesterday. When it will be fully assembled, I will put it back in the engine compartment and install the new intercooler, 2.5" turbo pipes, cold air tubes, 2.5" Blow-off alu flange, HKS SSQV Blow-off and 2.5" single throttle flap. A new hand made separate downpipe will be fabricated - one tube for the main flow out of the turbine, and smaller one for the gas through the wastegate. I will join the tubes just before the cat.

Next step will be the fuel delivery system. Finaly the ECU will be installed.

I ahve no idea when the project will be finished, but I have tones of patience. :twothumbsup:

Have a good time. When I have news I will post info.

Greetings to all of you.

Mike

Mike sorry to hear about the Father In-law illness. The medical term would be a Stroke in English. We wish a speedy recovery for him.

Keep us updated on your project.

Jeff

tabakoff
07-26-07, 02:00 AM
Thank you ... I hope he will recruit his health.

I will keep you informed.

Mike

tabakoff
08-05-07, 06:50 AM
Here I am again. I've got my exhaust manifold!!!:pepper: Looks perfect! I hope it will work well with my middle cams.

http://misho.avproxy.net/KILLER_GTI_Ehaust_Ram_Header_1_WEB.JPG
http://misho.avproxy.net/KILLER_GTI_Ehaust_Ram_Header_2_WEB.JPG
http://misho.avproxy.net/KILLER_GTI_Ehaust_Ram_Header_3_WEB.JPG
http://misho.avproxy.net/KILLER_GTI_Ehaust_Ram_Header_4_WEB.JPG
http://misho.avproxy.net/KILLER_GTI_Ehaust_Ram_Header_5_WEB.JPG
http://misho.avproxy.net/KILLER_GTI_Ehaust_Ram_Header_6_WEB.JPG
http://misho.avproxy.net/KILLER_GTI_Ehaust_Ram_Header_7_WEB.JPG

BurnTire
08-05-07, 11:18 AM
Looks Good Mike.
Getting closer to taking it to the drag strip.

silver03cobra
08-05-07, 06:16 PM
thats hot! keep posting pic's!

BurnTire
08-30-07, 03:08 PM
Got it running yet Mike?

dandzaman
08-31-07, 11:23 AM
interesting project my neighbour,but unpatience killing me...come on show as some more pics...

BurnTire
10-16-07, 10:10 PM
Any Progress Mike?

tabakoff
11-16-07, 08:11 AM
Hi boys,

Sorry for being away for such a long time, but I had some problems that I had to resolve.

First pictures are not so good, but I forgot my camera at home ....

This is my 16-valve head - full port and polish, combusion chamber had been remastered, all sharp edges and hot spots had been removed for better combusion and to avoid detonations.

http://misho.avproxy.net/605_16v_Head_Bottom_View_1_WEB.JPG

http://misho.avproxy.net/605_16v_Head_Bottom_View_2_WEB.JPG

http://misho.avproxy.net/605_16v_Head_Bottom_View_3_WEB.JPG

http://misho.avproxy.net/605_16v_Head_Bottom_View_4_WEB.JPG

http://misho.avproxy.net/605_16v_Head_Bottom_View_5_WEB.JPG

All valves in their places.

http://misho.avproxy.net/605_16v_Head_Bottom_View_6_WEB.JPG

http://misho.avproxy.net/605_16v_Head_Bottom_View_7_WEB.JPG

Exhaust valve guides had been shortened. We did a lot of work on the intake side because of merged ports.

http://misho.avproxy.net/605_16v_Head_Exhaust_Twin_Ports_WEB.JPG

http://misho.avproxy.net/605_16v_Head_Intake_Port_WEB.JPG

The new MLT gasket in place.

http://misho.avproxy.net/605_Engine_w_Gasket_1_WEB.JPG

http://misho.avproxy.net/605_Engine_w_Gasket_2_WEB.JPG

http://misho.avproxy.net/605_16v_Head_Tightened_WEB.JPG

Guess who is the nhappiest man in the world! Me, of course!

http://misho.avproxy.net/605_Someone_is_Happy_WEB.JPG

Here are some pictures of better quallity. We drop the car in my garage in this shape:

http://misho.avproxy.net/605_Front_View_WEB.JPG

We found this mesh .... I was a little bit stressed and confused and asking myself "Who will manage to remove all these wires".... My beloved wife!

http://misho.avproxy.net/605_Front_View_Open_Bonnet_WEB.JPG

http://misho.avproxy.net/605_Engine_Front_View_WEB.JPG

http://misho.avproxy.net/605_Hellen_in_the_Garage_WEB.JPG

tabakoff
11-16-07, 08:21 AM
The hard work began. Firstly I tried to install the exhaust manifold, just be sure that there is enough free space behind the engine block.

http://misho.avproxy.net/Exhaust_Manifold_WEB.JPG

I wanted to install the turbo at once... no way, I had to remove both turbine and comressor housings. Firstly I installed turbine housing, then the CHA and finally the compressor housing. It was OK.

http://misho.avproxy.net/Exhaust_Manifold_and_Turbo_WEB.JPG

Some of you have seen my intercooler parts ..... That was my intercooler some time ago.

http://misho.avproxy.net/Intercooler_Treadstone_WEB.jpg

http://misho.avproxy.net/Intercooler_Core_Close_View_Could_be_Better_WEB.jp g

http://misho.avproxy.net/Intercooler_Bar_n_Plate_Core_18.5x6x3_Vertical_Flo w_w_Tanks_WEB.jpg

And this is the intercooler now:

http://misho.avproxy.net/Intercooler_Assembled_Front_View_WEB.JPG

http://misho.avproxy.net/Intercooler_Assembled_Outlets_View_WEB.JPG

http://misho.avproxy.net/Intercooler_Assembled_Outlet_1_WEB.JPG

http://misho.avproxy.net/Intercooler_Assembled_Outlet_2_WEB.JPG

http://misho.avproxy.net/Intercooler_Assembled_Outlet_3_WEB.JPG

http://misho.avproxy.net/Intercooler_Assembled_Outlet_4_WEB.JPG

Nice work, I like it.

http://misho.avproxy.net/Intercooler_Assembled_Melting-pot_WEB.JPG

tabakoff
11-16-07, 08:30 AM
Next step was to remove the front fans.

They were placed at front of the radiators that was not good idea at all. I decided to place new onec behind them.

This is the front frame before Judjment Day.

http://misho.avproxy.net/2007-10-24_Fans_Before_Judgment_Day_WEB.JPG

http://misho.avproxy.net/2007-10-24_Fans_Passed_Judgment_WEB.JPG

Then I fixed the intercooler just to have idea where to place it.
http://misho.avproxy.net/2007-10-24_FMIC_Alignment_WEB.JPG

http://misho.avproxy.net/2007-10-24_FMIC_and_Tubes_Alignment_WEB.JPG

http://misho.avproxy.net/2007-10-24_Tubes_Passing_1_WEB.JPG

http://misho.avproxy.net/2007-10-24_Tubes_Passing_2_WEB.JPG

I was limitted from above

http://misho.avproxy.net/2007-10-24_FMIC_Limited_from_Above_WEB.JPG

So I decided to remaster the whole front frame generally.

http://misho.avproxy.net/2007-10-24_Front_Frame_WEB.JPG

http://misho.avproxy.net/2007-10-24_Front_Frame_Remains_WEB.JPG

This is how it looks like ... I installed the radiators too in order to chek for free space.

http://misho.avproxy.net/2007-10-24_Front_Frame_Remastered_WEB.JPG

http://misho.avproxy.net/2007-10-24_Front_Frame_Remastered_Installed_WEB.JPG

http://misho.avproxy.net/2007-10-24_Cooling_Radiator_Installed_WEB.JPG

http://misho.avproxy.net/2007-10-24_Clima_Radiator_Installed_WEB.JPG

Now it is much better!!!

There was enough space behind the cooling radiator so new SPAL fans will fit there.

http://misho.avproxy.net/2007-10-24_New_Fans_Available_Space_WEB.JPG

More or less looks fine.

http://misho.avproxy.net/2007-10-24_FMIC_Final_Check_1_WEB.JPG

http://misho.avproxy.net/2007-10-24_FMIC_Final_Check_2_WEB.JPG

tabakoff
11-16-07, 08:37 AM
Later on I started installing turbo pipes.

http://misho.avproxy.net/2007-11-03_0001_Version_1_Intercooler_Pipes_WEB.JPG

First try looked like that:

http://misho.avproxy.net/2007-11-03_0002_Version_1_Intercooler_Pipes_after_Turbo_WE B.JPG

http://misho.avproxy.net/2007-11-03_0003_Version_1_Pipes_Before_Turbo_WEB.JPG

http://misho.avproxy.net/2007-11-03_0004_Version_1_Intercooler_Pipes_after_Turbo_WE B.JPG

http://misho.avproxy.net/2007-11-03_0005_Version_1_Intercooler_Pipes_after_Turbo_WE B.JPG

http://misho.avproxy.net/2007-11-03_0006_Version_1_Pipes_Before_Turbo_WEB.JPG

I was out of silicone hoses so I went to the closest store .... damned, why all tuning parts in Bulgaria are much more expensive compared to the USA?!

I had to rearrange the pipes after the turbo:

http://misho.avproxy.net/2007-11-04_0017_Pipes_at_the_Turbo_WEB.JPG

http://misho.avproxy.net/2007-11-04_0018_Pipes_at_the_Turbo_WEB.JPG

http://misho.avproxy.net/2007-11-04_0019_Pipes_at_the_Turbo_WEB.JPG

Than started playing with the cold pipes.

http://misho.avproxy.net/2007-11-04_0001_Connecting_Pipes_WEB.JPG

http://misho.avproxy.net/2007-11-04_0002_Connecting_Pipes_WEB.JPG

http://misho.avproxy.net/2007-11-04_0003_Connecting_Pipes_WEB.JPG

http://misho.avproxy.net/2007-11-04_0007_All_Pipes_WEB.JPG

Turbo paths were a little bit changed:

http://misho.avproxy.net/2007-11-04_0008_All_Pipes_WEB.JPG

http://misho.avproxy.net/2007-11-04_0009_All_Pipes_WEB.JPG

http://misho.avproxy.net/2007-11-04_0013_All_Pipes_WEB.JPG

http://misho.avproxy.net/2007-11-04_0012_Intercooler_PIpes_WEB.JPG

http://misho.avproxy.net/2007-11-04_0004_Adjusting_Intercooler_WEB.JPG

http://misho.avproxy.net/2007-11-04_0005_Adjusting_Intercooler_WEB.JPG

http://misho.avproxy.net/2007-11-04_0010_Intercooler_in_Place_WEB.JPG

http://misho.avproxy.net/2007-11-04_0011_Intercooler_Inlets_and_Pipes_WEB.JPG

Now I had to choose how to fix the intercooler. So I got this allien:

http://misho.avproxy.net/2007-11-06_Alien_Intercooler_WEB.JPG

Now I need one 135 degrees and one 150 degrees bends, most probablly I will do that on Monday.

... Than there will be more pictures.:biglaugh:

tabakoff
11-16-07, 08:42 AM

chewbaccajones
11-16-07, 09:54 AM
Very nice! Looks like you have to be pretty good at improvising with the parts available to you in Bulgaria. The only exposure we get to Peugeot in the states is on Top Gear.

BurnTire
11-16-07, 11:34 AM
Wow Mike you have been busy. Looking Good!

Chris B.
11-16-07, 04:57 PM
WOW!!! Don't know how I missed out on this thread! This is great!!! Welcome to the site, although I'm a little late!!:biglaugh: Your project looks like it's coming along well!

BurnTire
03-24-08, 10:45 PM
Well Mike is this car terrorizing the streets of Bulgaria yet?

tabakoff
03-25-08, 02:24 AM
Not yet. :-( I am out of money one again. I have my dashboard prepared with the new Stewart Warner gauges, looks perfect, awesome.

I ordered new 11" SPAL fans with high flow under static pressure. They should arrive somewhere in the middle of April because are new series and are not available yet in the USA. :-( I wanted to order them directly from Italy, but the price was higher with more than $150 and with this lack of money there is no need to hurry for the fans since I have to remake my exhaust manifold ....

... I got tired with this manifold. The guy that made the first one had taken wrong dimensions and it touches the thermo insulation of the engine bay. Now we are manufacturing new one where the turbo will be arranged besides the engine block and right above the gear box bars.

I desperately hope that I will have about $3000 in a couple of weeks from another project and belive the car will be on the road at the end ot May.... I keep my fingers crossed.

Thank you guys for you interest in my project. I couldn't have ever belive that my project could have met such interest in this forum. Thank you for that!!!:bowdown::bowdown::bowdown:

May I ask the administrators to split my project from this theme and move it to a proper forum if possible? Just in order not to mess with the main subject of the theme.

Thank you again, I will keep you informed what's going on when I have some funds.

Best wishes to all of you, God bless you and your Stangs.

BurnTire
03-25-08, 11:00 AM
What would you like the title of the new thread to be?

tabakoff
03-26-08, 01:54 AM
Maybe "Peugeot 605 16v Turbo" will be best.

BurnTire
03-26-08, 11:09 AM
Maybe "Peugeot 605 16v Turbo" will be best.

Done :Bucktooth:

BurnTire
07-17-08, 01:20 PM
Any updates Mike?

This thread gets a ton of hits.

chewbaccajones
07-17-08, 07:30 PM
Damn, over 5700, you ain't lyin.

tabakoff
07-18-08, 12:47 AM
Hi again!!!

I was facing some major problems with my exhaust manifold. First manifold was too close to the engine bay and the guy who made it said it was not his fault and refused to remade it .....

Never mind ... I ordered yesterday one stainless steel manifold from DP-Engineering from the Netherlands .... these guys rock!!!!!!!

I managed to find -45mm springs from an UK dealer of SPAXX .... I hope these springs will do their job.

Last week I received my front shock absorbers by KONI - Red Special. The same type rear absorbers work great on my pug 605.

On Monday I will have my dashboard remade with the new Stewat-Warner gauges and will post some pictures.

My project goes slowly, but the money problem in Bulgaria takes part in my project too ...

BurnTire
07-18-08, 11:08 AM
Have fuel prices gone way up over there also?

tabakoff
07-18-08, 12:18 PM
Yes ... unfortunately ....

A-95 is $2.00 USD per litter .... This is toooooooooooooooooooooooooo much !!!

ASUSMC
07-18-08, 12:23 PM
aka $7.58 a gallon. OUCH

BUSTED
07-18-08, 07:48 PM
:gun3:the world should get together and mess these oil company's up......i mean not kill them, just scare them a little ya know.

Tr00nd605
10-10-08, 06:47 PM
Im Loving this project! Its a huge inspiration (or how its spelled) for me. I also have an Peugeot 605 Srti 93 mod. I havent started on the engine yet, but im not far away. So far ive done rims 18", front spoiler, brakes, exhaust (2.5" from engine all the way to the end) and a power air filter. :)

Can i ask how mutch your budget is for your car? how expensive is the engine upgrade?

CDW63
10-10-08, 08:22 PM
This is a great thread, very detailed project with great pictures. Thanks for sharing :goodidea:.

-Craig-

BurnTire
10-10-08, 10:53 PM
Ok it is time for Mike to reappear.

tabakoff
11-27-08, 01:11 AM
Hello boys!!! I am back again with my European project.:biglaugh:

I started the headlights HID Conversion. I removed the original halogen reflectors and installed the Bi-Xenon projectors from BMW.

http://misho.avproxy.net/605_HID_Conversion_1_WEB.JPG

http://misho.avproxy.net/605_HID_Conversion_2_WEB.JPG

http://misho.avproxy.net/605_HID_Conversion_3_WEB.JPG

http://misho.avproxy.net/605_HID_Conversion_4_WEB.JPG

I have a couple intake manifolds from Peugeot 605 .... Sorry, I HAD ... I cut of the throttle flap flange from one of them and did weld it to the manifold I will be using from Peugeot 306 S16 for the fastest Peugeot 605!!

http://misho.avproxy.net/605_SVti_Original_Intake_Rest_1_WEB.JPG

http://misho.avproxy.net/605_SVti_Original_Intake_Rest_2_WEB.JPG

That was the result:

http://misho.avproxy.net/605_S16_flange_to_Mi16_intake_1_WEB.JPG

http://misho.avproxy.net/605_S16_flange_to_Mi16_intake_2_WEB.JPG

http://misho.avproxy.net/605_S16_flange_to_Mi16_intake_3_WEB.JPG

tabakoff
11-27-08, 01:14 AM
I ordered one brand new turbocharger Turbonetics GT-K 350 ... again from the USA ....

http://misho.avproxy.net/Turbonetics_GT-K_350_0_WEB.JPG

http://misho.avproxy.net/Turbonetics_GT-K_350_1_WEB.JPG

http://misho.avproxy.net/Turbonetics_GT-K_350_2_WEB.JPG

http://misho.avproxy.net/Turbonetics_GT-K_350_3_WEB.JPG

http://misho.avproxy.net/Turbonetics_GT-K_350_4_WEB.JPG

http://misho.avproxy.net/Turbonetics_GT-K_350_5_WEB.JPG

http://misho.avproxy.net/Turbonetics_GT-K_350_6_WEB.JPG

http://misho.avproxy.net/Turbonetics_GT-K_350_7_WEB.JPG

http://misho.avproxy.net/Turbonetics_GT-K_350_8_WEB.JPG

http://misho.avproxy.net/Turbonetics_GT-K_350_9_WEB.JPG

tabakoff
11-27-08, 01:17 AM
My new Turbocharger kindly asked me to provide him with a new Wastegate .... I thing I have chosen the right gate for this pretty nice turbocharger.

http://misho.avproxy.net/TiAL_40.jpg

http://misho.avproxy.net/TiAL_F40_Racing_Valve_Stem.jpg http://misho.avproxy.net/TiAL_F40_assembly.jpg http://misho.avproxy.net/TiAL_F40.jpg http://misho.avproxy.net/TiAL_F40_304L_Stainless_Steel_Flange_WG40FLO-Discharge.jpg http://misho.avproxy.net/TiAL_F40_304L_Stainless_Steel_Flange_WG40FLI-Inlet.jpg

tabakoff
11-27-08, 01:22 AM
Proper turbocharger demands proper exhaust manifold .... Here is the manifold I ordered from DP-Engineering, Holland:
http://www.peugeotclub.info/forum/download/file.php?id=690

http://www.peugeotclub.info/forum/download/file.php?id=689

http://www.peugeotclub.info/forum/download/file.php?id=688

http://www.peugeotclub.info/forum/download/file.php?id=687

http://www.peugeotclub.info/forum/download/file.php?id=686

The manifold will be finnished here, in Bulgaria according to my specific vehichle.

tabakoff
11-27-08, 01:30 AM
The new dashboard is ready as well the new middle stand at the place of the middle ventilation unit.

http://misho.avproxy.net/Peugeot_6005_Dashboard_1_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Dashboard_2_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Dashboard_3_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Dashboard_4_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Dashboard_5_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Middle_Stand_1_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Middle_Stand_2_WEB.jpg

tabakoff
11-27-08, 01:35 AM
The KONI Special front absorbers and the SPAX springs also arrived:

http://www.peugeotclub.info/forum/download/file.php?id=294

http://misho.avproxy.net/Peugeot_6005_Front_Suspension_1_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Front_Suspension_2_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Front_Suspension_3_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Front_Suspension_4_WEB.jpg

The new BREMBO rotors and the 4-piston BREMBO calipers from Alfa Romeo 166 3.0 24V took their places.

http://misho.avproxy.net/Peugeot_6005_Front_Suspension_5_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Front_Suspension_6_WEB.jpg

tabakoff
11-27-08, 01:40 AM
The best place I found for the new ECU was the glove department .... wife, please have my apologies!!!

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_1_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_2_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_3_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_4_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_5_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_6_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_7_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_8_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_9_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_10_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_11_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_12_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_13_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_14_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_15_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_16_WEB.jpg

http://misho.avproxy.net/Peugeot_6005_Installing_ECU_Haltech_E8_17_WEB.jpg

BurnTire
11-27-08, 06:47 AM
Looks good Mike. Looks like you are getting closer to being done.

BurnTire
02-07-09, 11:49 PM
Got this running yet Mike?

02stangGT
02-08-09, 12:29 AM
welcome!

BurnTire
09-06-09, 05:55 PM
All the pictures are gone. :gloomy: